活塞環在使用中易出現嚴重磨損彈力減弱，內部結膠及折斷等故障?；钊h(huán)在長期的使用過程中，受到高溫高壓和往復運動的影響，會出現磨損。當磨損達到一定程度時，活塞環的彈力開始減退，端隙側隙和背隙也會逐漸增大，對燃燒室的密封作用會減弱。在活塞環的密封作用減弱后，柴油噴人燃燒室后就會出現燃燒不完全，燃燒室內產生的高溫氣體會通過活塞環的間隙進入曲軸箱，使活塞環內積炭增多，密封作用的減弱，也造成了潤滑油上竄，使用的時間越長，活塞環內部結膠就會越多?；钊h(huán)折斷一般是由于裝配方法不正確或活塞環被積炭卡死所造成。

The piston ring is prone to severe wear, weakened elasticity, internal bonding, and breakage during use. During long-term use, piston rings may experience wear due to the influence of high temperature, high pressure, and reciprocating motion. When the wear reaches a certain level, the elasticity of the piston ring begins to decrease, and the end gap, side gap, and back gap gradually increase, weakening the sealing effect on the combustion chamber. After the sealing effect of the piston ring weakens, incomplete combustion will occur when diesel is injected into the combustion chamber. The high-temperature gas generated in the combustion chamber will enter the crankcase through the gap of the piston ring, causing more carbon deposits in the piston ring. The weakening of the sealing effect also causes lubricating oil to flow up. The longer the use time, the more adhesive will accumulate inside the piston ring. A broken piston ring is usually caused by incorrect assembly methods or the piston ring being stuck by carbon deposits.

燃氣發電機

Gas generator

燃氣發電機活塞環開口間隙的確定

Determination of piston ring opening clearance in gas generators

活塞環裝人氣缸后，切口處必須保持一定的間隙，此間隙稱為活塞環的閉口間隙。若裝人氣缸后的間隙過小，活塞環會受氣缸內高溫的影響而膨脹致使活塞環折斷；若裝人氣缸后的間隙過大，則會使活塞環出現嚴重漏氣，導致柴油機功率不足，并會引發一系列故障。因此，維修人員在裝配活塞環時一定要按柴油機維護說明書中的規定執行。

After the piston ring is installed in the cylinder, a certain gap must be maintained at the incision, which is called the closed gap of the piston ring. If the gap after installation in the cylinder is too small, the piston ring will expand due to the high temperature inside the cylinder, causing the piston ring to break; If the gap after installing the cylinder is too large, it will cause serious air leakage in the piston rings, resulting in insufficient power of the diesel engine and causing a series of malfunctions. Therefore, maintenance personnel must follow the regulations in the diesel engine maintenance manual when assembling piston rings.

燃氣發電機活塞環損壞的故障現象及修理

Fault phenomenon and repair of damaged piston rings in gas generators

燃氣發電機在運轉中排氣管冒黑煙藍煙，或潤滑油內進入柴油且功率急速下降時，一般可認為是活塞環出現故障所致?；钊h(huán)價格較低，損壞后一般換用新件即可。

When the exhaust pipe of a gas generator emits black and blue smoke during operation, or when the lubricating oil enters diesel and the power drops rapidly, it can generally be considered as a failure of the piston ring. The price of piston rings is relatively low, and after damage, they are usually replaced with new parts.

燃氣發電機活塞環平裝進氣缸套內，接口處要有必然的開口間隙。

The piston ring of the gas generator should be installed flat into the cylinder liner, and there should be a certain opening gap at the interface.

（1容量的確定：按機組長期持續運行輸出功率能滿足全工程計算負荷選擇，在環槽中，沿高度方向要有必然的邊間隙。超級豪華車的服務承諾是全球24小時到達（包括所需要配件，開口不要對著活塞頂部的渦流凹坑方向。

(1) Determination of capacity: According to the long-term continuous operation of the unit, the output power can meet the load selection of the entire engineering calculation. In the ring groove, there must be a certain edge gap along the height direction. The service commitment of the super luxury car is to arrive 24 hours a day worldwide (including required accessories, the opening should not face the direction of the vortex pit at the top of the piston).

（2臺數的確定：一般設置通常為2臺以上，倒角或切槽應向上。

(Determination of the number of 2 units: Generally, there are more than 2 units, and the chamfer or groove should be facing upwards.).

安裝組合環時，以保證供電的連續性及適應用電負荷曲線的變化，再裝扁平環和波形環。波形環上邊裝兩片扁平環，才可以根據用電負荷的變化確定投入發電機組的進行臺數，開口應相互錯開。

When installing the combination ring, to ensure the continuity of power supply and adapt to changes in the electricity load curve, then install the flat ring and waveform ring. Two flat rings are installed on top of the waveform ring to determine the number of units to be put into the generator set based on changes in electricity load, and the openings should be staggered from each other.

各活塞環開口在互相錯開120℃，并應根據負荷的重要性確定發電機組備用機組容量，

The openings of each piston ring should be staggered by 120 ℃ from each other, and the standby capacity of the generator set should be determined based on the importance of the load,

錐形斷面活塞環，安裝時錐面應向上。

The conical section piston ring should be installed with the conical surface facing upwards.